Hyundai Sonata: Brake Booster. Repair procedures - Brake System - Brake SystemHyundai Sonata: Brake Booster. Repair procedures

Brake Booster Operating Test

For simple checking of the brake booster operation, carry out the following tests.
1.
Run the engine for one or two minutes, and then stop it. If the pedal depresses fully the first time but gradually becomes higher when depressed succeeding times, the booster is operating properly, if the pedal height remains unchanged, the booster is inoperative.
2.
With the engine stopped, step on the brake pedal several times.
Then step on the brake pedal and start the engine. If the pedal moves downward slightly, the booster is in good condition. If there is no change, the booster is inoperative.
3.
With the engine running, step on the brake pedal and then stop the engine.Hold the pedal depressed for 30 seconds. If the pedal height does not change, the booster is in good condition, if the pedal rises, the booster is inoperative.
If the above three tests are okay, the booster performance can be determined as good.
Even if one of the above three tests is not okay, check the check valve, vacuum hose and booster for malfunction.

Removal

Brake Booster
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the air cleaner assembly (A).
3.
Disconnect the vacuum hose (A) from the brake booster.
4.
Remove the master cylinder.
(Refer to the master cylinder)
5.
Remove the brake tube (A).
Tightening torque:
18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.7 lb-ft)

6.
Remove the snap pin (A) and clevis pin (B).
7.
Remove the mounting nuts.
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

8.
Remove the brake booster.
Vacuum Pump
1.
Turn ignition switch OFF.
2.
Remove the under covers (A, B).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

When removing the under cover (B), unfasten the mounting bracket bolts and then remove the under cover and mounting bracket assembly.
3.
Disconnect the vacuum pump connector (A).
4.
Disconnect the vacuum hose (A).
5.
Loosen the vacuum pump bracket bolts (A), and then remove vacuum pump and bracket.
Tightening torque:
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

6.
Remove the 2 bolts, and then remove the bracket from vacuum pump.

Inspection

1.
Inspect the check valve in the vacuum hose, intensifier and the connecting section.
Do not remove the check valve from the vacuum hose.
2.
Check the boot for damage.
Vacuum Pump
1.
Check the brake warning lamp in the IGN ON position.
Brake warning lamp is ON as below conditions.
1.
Parking brake warning
2.
Low brake fluid level warning
3.
Low brake vacuum pressure warning
-
Vacuum pump is abnormal condition
-
Vacuum pump CAN communication is abnormal condition
-
Vacuum switch is abnormal condition
2.
Check that the brake warning lamp is ON after the release the parking brake with a sufficient brake fluid level.
If the brake warning lamp is ON, check the below points.
(1)
Is the brake warning lamp ON within 5 seconds after IGN ON? (CAN Timeout Error)
CAN Timeout Error ; The brake warning lamp is ON when the communication fails more than 2 seconds between vacuum pump and cluster.

▶ Reinstall the vacuum pump connector after removing it. And if the brake warning lamp is ON within 5 seconds after IGN ON, replace the vacuum pump.

▶ Check the 2).

(2)
Is the brake warning lamp ON within 45 ~ 55 seconds?

 ▶ Brake vacuum switch is normal condition.

▶ Check the 3).

(3)
Is the brake warning lamp ON within 15 ~ 35 seconds after removing the vacuum hose from the brake booster?

 ▶ Replace the vacuum pump.

▶ Vacuum pump is normal condition.


Installation

Brake Booster
1.
Installation is the reverse of removal.
•
Before installing the pin, apply the grease to the joint pin.
•
Use a new snap pin whenever installing.
2.
Adjust the brake pedal height and free play.
(Refer to Brake pedal height and free play adjustment)
Vacuum Pump
1.
Installation is the reverse of removal.
2.
Tighten the vacuum pump mounting bolts to the specified torque.

    Brake Booster. Components and Components Location
    Components (1) 1. Brake booster 2. Master cylinder assembly 3. O-ring Components (2) 1. Vacuum pump 2. Bracket ...

    Master Cylinder. Components and Components Location
    Components 1. Reservoir cap 2. Reservoir 3. Grommet 4. Master cylinder ...

    See also:

    Parking Brake Assembly. Repair procedures
    Removal Parking Brake Pedal [Foot type] 1. Remove the crash pad lower panel. (Refer to the Body group-crash pad) 2. Remove the junctio ...

    AVN Head Unit. Repair procedures
    Removal AVN Head Unit • Take care not to scratch the center fascia panel and related par ...

    Components and Components Location
    Components Location 1. PCV Valve 2. Canister 3. Purge Control Solenoid Valve (PCSV) 4. Fuel Tank Pressure Sensor (FTPS) 5. Canister Close Valve (CCV) 6. Fuel ...