Hyundai Sonata: Side Impact Sensor (SIS). Repair procedures - SRSCM - RestraintHyundai Sonata: Side Impact Sensor (SIS). Repair procedures

Hyundai Sonata YF 2011-2014 Service Manual / Restraint / SRSCM / Side Impact Sensor (SIS). Repair procedures

Removal

Pressure Side Impact Sensor
•
Removal of the airbag must be performed according to the precautions/procedures described previously.
•
Before disconnecting the side impact sensor connector(s), disconnect the side airbag connector(s).
•
Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front door trim. (Refer to the Body group- Front door)
3.
Disconnect the pressure side impact sensor connector (A) and remove the pressure side impact sensor mounting screws (B).
Side Impact Sensor
1.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
2.
Remove the door scuff trim. (Refer to the Body group - Interior trim)
3.
Remove the center pillar trim. (Refer to the Body group - Interior trim)
4.
Disconnect the side impact sensor connector.
5.
Loosen the side impact sensor mounting bolt and remove the side impact sensor.

Installation

Pressure Side Impact Sensor
1.
Install the new pressure side impact sensor with the screws then connect the pressure side impact sensor connector.
Tightening torque :
3.5 ~ 4.5 N.m (0.36 ~ 0.46 kgf.m, 2.6 ~ 3.3 lb-ft)
•
Use the specified screws surely.
2.
Install the front door trim. (Refer to the Body group- Front door)
3.
Reconnect the battery negative cable.
4.
After installing the pressure side impact sensor, confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
•
You must comply with the specified tightening torques with the tool specified because Pressure – Side Impact Sensors (P-SIS) may be broken or POP-NUT may be rotated.
•
Problems may be occurred in the durability of P-SIS or impact sensing performance may be depreciated if POP-NUT is rotated.
•
The door module must not be transformed because SRSCM judges a impact through the pressure sensor in the door module.
Side Impact Sensor
•
Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.
1.
Install the new side impact sensor with the bolt then connect the side impact sensor connector.
Tightening torque:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)
2.
Install the center pillar trim (Refer to the Body group - Interior tirm)
3.
Install the door scuff trim. (Refer to the Body group - Interior tirm)
4.
Reconnect the battery negative cable.
5.
After installing the Side Impact Sensor, confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

    Seat Track Position Sensor (STPS). Description and Operation
    Description The STPS operates via a non-contacting magnetic proximity sensing device combined with a simple electronic circuit resulting in the ability of producing two separate and distinct ...

    See also:

    Wheel replacement
    When replacing the metal wheels for any reason, make sure the new wheels are equivalent to the original factory units in diameter, rim width and offset. WARNING A wheel that is not the correct siz ...

    Seat belt warning (for driver’s seat)
    The driver's seat belt warning light and chime will activate to the following table when the ignition switch is in "ON" position. *1 Warning pattern repeats 11 times with an inter ...

    Tilt steering
    Tilt steering allows you to adjust the steering wheel before you drive. You can also raise it to give your legs more room when you exit and enter the vehicle. The steering wheel should be positione ...