Hyundai Sonata: Sunroof. Repair procedures - Exterior - Body (Interior and Exterior)Hyundai Sonata: Sunroof. Repair procedures

Replacement

Glass Replacement
-
Put on glove to protect your hands.
1.
Remove the glass (A) by lifting it up.
-
Do not damage the roof panel.

2.
Installation is the reverse of removal.
Motor Replacement
1.
Remove the over head console.
-
Confirm the position of guide whether it is closed or not when you remove the motor.
2.
Disconnect the motor connector (A), remove the screws and then remove the motor (B).
3.
Installation is the reverse of removal.
Deflector Replacement
1.
Open the glass fully.
2.
Disconnect the deflector link (A) from the frame (B), and then remove the deflector (C).
3.
Installation is the reverse of removal.
Sunroof Assembly Replacement
1.
Remove the follows parts.
A.
Front and door scuff trim.
B.
Front, center and rear pillar trim.
C.
Headlining.
D.
Sunroof glass.
2.
Disconnect the drain tubes (A).
3.
After loosening the mounding bolts and nuts, remove the sunroof assembly (B).
-
Take care not to scratch the interior trims and other parts.
4.
Installation is the reverse of removal.

Sunshade And Drip Rail Replacement
1.
Remove the sunroof assembly.
2.
Remove the drip link (A) and sunshade stopper (B).
3.
Remove the sunshade (C) and drip rail (D).
4.
Installation is the reverse of removal.
Guide Assembly Replacement
1.
Remove the sunroof assembly.
2.
Remove a guide assembly (A) after lowering a guide thoroughly by pushing a slide to rear.
3.
Remove the guide (A) and slide (B).
4.
Installation is the reverse of removal.
-
Make sure to align the slide with the center of “A” and “B”
-
Make sure to initialize the motor.

Adjustment

How To Initialize
1.
Check that the glass has been installed.
A.
Finished height adjustment.
2.
Push the down switch. (Keep on pushing the switch)
A.
The slide moved 5mm forward after 15 seconds.

3.
After moving the slide 5mm forward, turn OFF the switch and push the down switch (Keeping on pushing the switch with continuous operation).
A.
If the operation above is normal condition, the sunroof once and closes.
4.
When the sunroof is closed completely, turn OFF the down switch initialize the motor completely.
When To Initialize The Motor
1.
First operation in the vehicle after manufacture it.
2.
Initial value is erased or damaged because of short power electric discharge during operation.
3.
After using the manual (emergency) handle.

    Sunroof. Components and Components Location
    Components 1. Glass panel assembly 2. Drip link 3. Guide assembly 4. Sunshade assembly 5. Drip rail 6. Deflector 7. Deflector link assembly 8. Sunroof ...

    Panoramaroof. Components and Components Location
    Components 1. Roof molding 2. Movable glass 3. Wind deflector 4. Front cover assembly 5. Roller blind 6. Mechanism assembly 7. Motor 8. Cover ...

    See also:

    Accelerator Position Sensor (APS). Specifications
    Specification Accelerator Position Output Voltage (V) APS1 APS2 C.T 0.7 ~ 0.8 0.29 ~ 0.46 ...

    Manual transaxle operation
    The shift lever can be moved into any of the forward gears without pulling the ring (1). The ring (1) must be pulled while moving the shift lever into reverse. The manual transaxle has 6 forw ...

    Repair procedures
    Clutch Pedal Inspection And Adjustment 1. Measure the clutch pedal height (from the face of the pedal pad to the floorboard) and the clutch pedal clevis pin play (measured ...