Symption
|
Suspect area
|
Remedy
|
Engine misfire with abnormal internal lower engine noises.
|
Worn crankshaft bearings
Loose or out of specification engine flywheel
|
Replace the crankshaft and bearings as required.
Repair or replace the flywheel as required.
|
Worn piston rings
(Oil consumption may or may not cause the engine to misfire.)
|
Inspect the cylinder for a loss of compression.
Repair or replace as required.
|
Worn crankshaft thrust bearings
|
Replace the crankshaft and bearings as required
|
Engine misfire with abnormal valve train noise.
|
Stuck valves.
(Carbon buidup on the valve stem)
|
Repair or replace as required
|
Excessive worn or mis-aligned timing chain
Out of specification valve clearances
|
Replace the timing chain and sprocket as required.
|
Worn camshaft lobes.
|
Replace the camshaft and valve lifters.
|
Engine misfire with coolant consumption
|
| •
|
Faulty cylinder head gasket or other damage
to the cylinder head and engine block cooling system.
|
| •
|
Coolant consumption may or may not cause
the engine to overheat.
|
|
| •
|
Inspect the cylinder head and engine block
for damage to the coolant passages and/or a faulty head gasket.
|
| •
|
Repair or replace as required.
|
|
Engine misfire with excessive oil consumption
|
Worn valves, guides and/or valve stem oil seals.
|
Repair or replace as required.
|
Worn piston rings.
(Oil consumption may or may not cause the engine to misfire)
|
| •
|
Inspect the cylinder for a loss of compression.
|
| •
|
Repair or replace as required.
|
|
Engine noise on start-up, but only lasting a few seconds.
(Check and compare with known good vehicle to determine
normal condition.)
|
Incorrect oil viscosity
|
| •
|
Install the correct viscosity oil.
|
|
Worn crankshaft thrust bearing.
|
| •
|
Inspect the thrust bearing and crankshaft.
|
| •
|
Repair or replace as required.
|
|
Upper engine noise, regardless of engine speed.
|
Low oil pressure
|
Repair or replace as required.
|
Broken valve spring.
|
Replace the valve spring.
|
Worn or dirty valve lifters.
|
Replace the valve lifters.
|
Stetched or broken timing chain and/or damaged sprocket
teeth.
|
Replace the timing chain and sprockets.
|
Worn timing chain tensioner, if applicable.
|
Replace the timing chain tensioner as required.
|
Worn camshaft lobes.
|
| •
|
Inspect the camshaft lobes.
|
| •
|
Replace the timing camshaft and valve lifters
as required.
|
|
Out of specification valve clearances
Worn valve guides or valve stems.
|
Inspect the valves and valve guides, then repair or replace
as required.
|
Stuck valves. (Carbon on the valve stem or valve seat
may cause the valve to stay open.
|
Inspect the valves and valve guides, then repair or replace
as required.
|
Worn drive belt, idler, tensioner and bearing.
|
Replace as required
|
Lower engine noise, regardless of engine speed
|
Low oil pressure
|
Repair or required.
|
Loose or damaged flywheel.
|
Repair or replace the flywheel.
|
Damaged oil pan, contacting the oil pump screen.
|
| •
|
Inspect the oil pump screen.
|
| •
|
Repair or replace as required.
|
|
Oil pump screen loose, damaged or restricted.
|
| •
|
Inspect the oil pump screen.
|
| •
|
Repair or replace as required.
|
|
Excessive piston-to-cylinder bore clearance.
|
| •
|
Inspect the piston, piston pin and cylinder
bore.
|
| •
|
Repair or replace as required.
|
|
Excessive piston pin-to-piston clearance
|
| •
|
Inspect the piston, piston pin and the connecting
rod.
|
| •
|
Repair or replace as required.
|
|
Excessive connecting rod bearing clearance
|
Inspect the following components and repair or replace
as required.
| •
|
The connecting rod bearings.
|
| •
|
The crankshaft pin journals.
|
|
Excessive crankshaft bearing clearance
|
Inspect the following components, and repair or replace
as required.
| •
|
The crankshaft bearings.
|
| •
|
The crankshaft main journals.
|
|
Incorrect piston, piston pin and connecting rod installation
|
| •
|
Verify the piston pins and connecting rods
are installed correctly.
|
|
Engine noise under load
|
Low oil pressure
|
Repair or replace as required.
|
Excessive connecting rod bearing clearance
|
Inspect the following components and repair or replace
as required :
| •
|
The connecting rod bearings.
|
|
Excessive crankshaft bearing clearance
|
Inspect the following components, and repair or replace
as required.
| •
|
The crankshaft bearings.
|
| •
|
The crankshaft main journals.
|
|
Engine will not crank-crankshaft will not rotate
|
Hydraulically locked cylinder
| •
|
Coolant/antifreeze in cylinder.
|
|
| 1. |
Remove spark plugs and check for fluid.
|
| 2. |
Inspect for broken head gasket.
|
| 3. |
Inspect for cracked engine block or cylinder
head.
|
| 4. |
Inspect for a sticking fuel injector and/or
leaking fuel regulator.
|
|
Broken timing chain and/or timing chain and/or timing
chain gears.
|
| 1. |
Inspect timing chain and gears.
|
|
Material in cylinder
|
| 1. |
Inspect cylinder for damaged components and/or
foreign materials.
|
| 2. |
Repair or replace as required.
|
|
Seized crankshaft or connecting rod bearings.
|
| 1. |
Inspect crankshaft and connecting rod bearing.
|
|
Bent or broken connecting rod.
|
| 1. |
Inspect connecing rods.
|
|
Broken crankshaft
|
|
Hyundai Sonata: Troubleshooting
Repair procedures
Special Service Tools